How To Clean Rotery Attachment In Epilog Laser
Fusion Rim-Drive Rotary Attachment
The Standard Rim-Bulldoze Rotary Attachment allows you lot to engrave wine bottles, mugs, glasses and more than.
Available for the Fusion M2 Laser, the Standard Rotary Attachment adds the power to engrave bottles, glasses, flashlights, or whatever other cylindrical item up to eleven.25" (286 mm) in diameter. The Fusion M2 Laser rotary attachment has been built to accommodate a big multifariousness of shapes and sizes. Setup is as easy as placing your product on the Rotary Attachment, raising or lowering the scissor lift to level the engraving expanse, and printing to the laser!
Fusion 3-Jaw Chuck Rotary Attachment
When more precision is required, the three-Jaw Chuck Rotary Attachment is the ideal choice.
But bachelor for the Fusion M2 Laser, the 3-Jaw Chuck mechanically clamps a cylinder or oddly-shaped, non-cylindrical item place as the laser engraves.
The Fusion M2 Laser rotary zipper has been built to accommodate a large variety of shapes and sizes. Setup is as piece of cake equally placing your product on the Rotary Attachment, raising or lowering the scissor elevator to level the engraving surface area, and printing to the laser!
Vector Cutting Tabular array
Raises laser cut materials off the table for better edges.
Incorporate the gridded cutting table on your Fusion light amplification by stimulated emission of radiation system when cutting through materials. By raising the materials when cutting off the table, you'll be able to reduce the back-side burning on the textile.
PhotoLaser Plus Software
Photo processing software that optimizes your photographs for engraving on a variety of materials.
PhotoLaser Plus takes photo engraving with your Epilog light amplification by stimulated emission of radiation to the adjacent level by easily processing photos for engraving on all types of materials.
Are you looking for a system that engraves outstanding photographs? How about a system that engraves photos in a consistent, predictable way for your customers?
Epilog Laser has partnered with CADLink to bring yous the industry's best photo processing software: PhotoLaser Plus. The like shooting fish in a barrel-to-utilise software interface and powerful photo processing tools allow you lot to create the highest-quality photo engravings in the manufacture.
Optional Lenses
In addition to the two.0" lens, we offer special lenses for specific applications.
one.5" Lens: Highest-Resolution Engraving
Although the standard 2.0 inch lens provides amazing particular, our one.5-inch lens associates has been designed for the highest-resolution engraving and carving of extremely small fonts.
4.0" Lens: Cutting Thicker Materials and Within Deep Areas
The 4.0 inch lens produces a focused axle over a longer vertical distance, which makes it ideal when engraving inside a recessed surface area of a product, such as within a basin or plate. The lens is too used for cutting through very thick materials.
Cone Lens: Deep Cutting with the Light amplification by stimulated emission of radiation
The Cone pattern pushes the stream from the Air Assist downwardly directly through the cut, rather than over the surface of the engraving material. This provides even improve reduction of laser flare-ups and improve edge quality.
Vector Pin Table
Raise and support your cutting materials for better border quality.
The Pin Table incorporates movable pins that tin can exist placed anywhere along the table's grid of 1 inch (25.four mm) spaced holes. The movable pins also allow the user to enhance and support the cutting fabric in locations where the laser will not be cut, providing a means of eliminating backside reflection. The table also allows you to identify pins to back up parts that would normally fall out of the cutting pattern. A handy removable surface plate makes the task of cleaning upwards modest parts easy without removing the Pin Tabular array.
Air Compressor
Blows a constant stream of air on the cutting area.
Epilog's optional Air Compressor is available to piece of work with the included Air Assist features of the light amplification by stimulated emission of radiation systems. Directly a abiding stream of air to your cut surface to remove heat and combustible gases from the work area.
This high-quality air compressor unit feeds 30 psi of air through the Air Assist structure, giving yous the best cutting results bachelor. The safety vibration-dampening feet reduce the racket level of the compressor, and connection is a breeze with our quick-connect inlet and outlet ports on the compressor and the laser organisation.
Source: https://www.bestequipmentsales.com/epilog-laser/fusion-accessories.htm
Posted by: mcbridefarretionly.blogspot.com

0 Response to "How To Clean Rotery Attachment In Epilog Laser"
Post a Comment